The LM series are precision easily-calibrated integrat- ed circuit temperature sensors Operating as a 2-terminal zener the LM has a breakdown voltage. lm are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for lm Data sheet, LM manual, LM pdf, LM, datenblatt, Electronics LM, alldatasheet, free, datasheet, Datasheets, data sheet, datas sheets, databook.

Author: Mabei Gujora
Country: Austria
Language: English (Spanish)
Genre: Politics
Published (Last): 11 July 2017
Pages: 425
PDF File Size: 8.8 Mb
ePub File Size: 13.60 Mb
ISBN: 380-6-92732-716-2
Downloads: 50925
Price: Free* [*Free Regsitration Required]
Uploader: Vigore

View lm355 datasheet:

As a temperature sensor, the circuit will read the temperature of the surrounding environment and relay this temperature to us back in degrees Kelvin. This is so that we can hook our arduino to a computer and lmm355 it code that it can run to display to us the temperature. The code satasheet shown below. The arduino, with suitable code, can then interpret this measured analog voltage and output to us the temperature in degrees Kelvin, Celsius, and Fahrenheit.

So you circuit connections are: Datsheet 3 are calibrated different to output the millivolt voltage reading in proportional to these different units of measurement. So if the LM is giving an output reading of 2. The raw voltage over this value therefore represents the ratio of how much power the output pin is outputting against this full range. You can adjust this value to meet your personal preference or program needs. This will be the raw value divided lm355 times This allows us to calibrate the temperature sensor if we want datasjeet more precise temperature readout.

The dtaasheet pin provides an analog voltage output that is linearly proportional to the fahrenheit temperature. Pin 2 is the output pin. Pin 1 is the Adjustable Pin Adj. This is because there is millvolts in 5 volts.


This is ideal because the arduino’s power pin gives out 5V of power. The difference between an LM and LM34 and LM35 temperature sensors is the LM sensor gives out the temperature in degrees Kelvin, while the LM35 sensor gives out the temperature in degrees Celsius and the LM34 sensor datasheeet out the temperature in degrees Fahrenheit.

We can then easily convert this value into fahrehnheit and celsius by plugging in the appropriate conversion equations. Once this analog voltage in millivolts is calculated, we then can find the temperature datasyeet kelvin by the equation: All we must do is write this code and upload it to the arduino to convert this kelvin temperature into fahrenheit and celsius.

This is the datasheet of the LM IC: We can now write code in the processing software to give instructions to the arduino. It is divided by because a span of occupies 5V.

Temperature Sensor Circuit The temperature sensor circuit we will build is shown below: Pin 2 gives datashfet output of 1 millivolt per 0. Before we can get a Kevlin reading of the temperature, the analog output voltage must first be read. We will integrate this with the arduino to measure the temperature.

We can use any type of arduino board. The arduino will then read this measured value from the LM and translate into degrees kelvin, fahrenheit and celsius, which we will be able to read from the computer from the arduino serial monitor. Now the computer is connected to the arduino. We attach this pin to analog pin A0 of the arduino board.


LM Datasheet, PDF – Alldatasheet

So to get the degree value in fahrenheit, all that must be done is to take the voltage output and divide it by this give out the value degrees in fahrenheit. We get the ratio of the raw value to the full span of and then multiply it by to get the millivolt value. This translates into the circuit schematic: This output reading of Since the output pin can give out a maximum of 5 voltsrepresents the full possible range it can give out.

Once we obtain this Celsius value, we can convert into Fahrenheit with the following equation: Once we have this ratio, we then multiply it by to give the millivolt value. Pin 3 is the ground pin and connects to the ground GND terminal of the arduino. Below is the pinout of the LM IC: The type B side of the connector goes into the arduino and the type A side into the USB port of the computer.

In this project, we will demonstrate how to build temperature sensor circuit using a LM sensor. So, datasheeg example, if the output pin, pin 2, gives out a value of mV 0.

All you have to do is take the output reading and divide it by 10 in order to get the temperature output reading. The IC has just 3 pins, 2 for the power supply and one for the analog output.